Departing Traffic

We ask all pilots to also read the General section with information relevant to all pilots.

Preparation

A thorough preparation is important for any flight. We ask you to conduct a thorough briefing to avoid delays and keep it fun for everyone.

Route planning

You can find valid routes for many destinations in the AeroNav Global Route Database.

When planning a route via SimBrief, please use routes with the Eurocontrol icon, as those will generally be valid.

When filing an invalid flight plan, you will usually have to file a completely new flight plan before ATC can issue your enroute clearance.

SID assignment

ATC will assign SIDs according to the table below. If the first waypoint of your flight plan is not listed here, please check which AIRAC you are using - if your AIRAC cycle is too outdated, it might take some time until the controllers can coordinate a solution for you. Please also make sure you are complying with the restrictions for each of the available initial waypoints.

Default SID assignment

Waypoint	07	25	Restrictions
DOMEG	E	C
HMM	Y	Z	07 operations: only (turbo-)prop up to 5.7t MTOM 25 operations: jet aircraft only up to 20t MTOM
OSN	E	C
RKN	E	C

Enroute Clearance

Clearance requests in Germany are very short. Please avoid unnecessarily long clearance requests to reduce frequency congestion.

Pilot: Münster Ground, Lufthansa 5EK, stand 12, request enroute clearance, information M.

Datalink Clearance (DCL)

Münster/Osnabrück also offers electronic datalink clearances (also known as PDC or Pre-Departure Clearance) on VATSIM using the Hoppie ACARS system. The station code is EDDG. If your aircraft does not have a direct integration of the Hoppie system, you can also use easyCPDLC.

Requesting clearance electronically is preferred over voice clearances as it reduces frequency congestion thus avoiding delays. Because of this, we ask all pilots able to use the Hoppie ACARS system to do so.

Startup

Startup approval is the "go" from the controller's side to start your engines. It is also an assurance that you will be cleared to start moving within the next 20 minutes. It can be requested and approved together with pushback.

Pushback

Only request pushback if you are actually ready to start pushing back. If you take longer than 1 - 2 minutes to start moving, ATC might have to cancel your pushback clearance to avoid delays for other pilots.

Keep in mind that some positions on Münster/Osnabrück's apron are taxi-out stands. If you are parked on one of these taxi-out stands, you won't need a pushback.

If you are unsure about your pushback instruction or unable to comply for any reason, hold position and inform ATC immediately.

Taxi

While Münster/Osnabrück's layout is relatively simple, it is still important to conduct a thorough briefing of expected taxi routes as well as correct taxiing. To avoid delays for yourself and other users, start taxiing as soon as possible after receiving your taxi clearance and request taxi in a timely manner after your pushback.

If you are unsure about your taxi instructions, hold position and inform ATC immediately.

Run-up

There are run-up areas at runway intersections A and B, called A1 and B1. If you require a run-up, inform Münster Ground as early as possible so they can issue an appropriate instruction.

Takeoff

Münster/Osnabrück has only one runway which needs to be used for both departures and arrivals. While there is usually not too much other traffic, it is still important to begin your takeoff roll as soon as you receive your clearance and be prepared for immediate takeoff clearances. If you take too long, ATC might have to cancel your takeoff clearance and issue a go around for an arriving aircraft.

Auto-handoff

Münster/Osnabrück utilizes an auto-handoff procedure for IFR departures where Tower will not hand off outbounds to the approach controller. The current airborne frequency will always be noted in the ATIS.

Contact the airborne frequency immediately when airborne unless explicitly told to remain on Tower frequency.