Skip to main content

ATIS Codes

Default ATISmaker URL

http://uniatis.net/atis.php?metar=$metar($atisairport)&arr=$arrrwy($atisairport)&dep=$deprwy($atisairport)&apptype=ILS&info=$atiscode

The above URL is designed for Euroscope versions with only one ATIS. For the newest Euroscope versions with four ATISes, the letters A, B, C, or D need to be appended to the $atisairport and $atiscode parameters (e.g. $atisairportA for the first ATIS).

General ATIS Codes

Add the following code at the end of the ATISmakerURL to include the ATIS broadcast message. For all airports except Frankfurt the departure frequency has to be included in the ATIS!

CODE Broadcast
&depfreq=123.123 ATTENTION! DEPARTURE FREQUENCY FOR ALL DEPARTING AIRCRAFT IS 123.123
&lvp LOW VISIBILITY PROCEDURES IN OPERATION CAT II AND III AVAILABLE

&gto (do not use together with &lvp; at EDDF: DEP ATIS only)

 LOW VISIBILITY PROCEDURES IN OPERATION CAT III AND GUIDED TAKE-OFF AVAILABLE FOR RUNWAY [...]

EDDF ATIS Codes

Manual Setup
CODE Broadcast
&atistype=dep
 sets the desired ATIS as departure ATIS (mandatory!)
&atistype=arr
 sets the desired ATIS as arrival ATIS (mandatory!)
&acdm (DEP) ALL IFR DEPS REPORT TOBT AT VACDM.VATGER.DE BEFORE REQ ENROUTE CLEARANCE
&alternate (ARR) EXPECT ILS [...]
&birds CAUTION FLOCK OF BIRDS IN VICINITY OF THE AERODROME
&ilsz (ARR)
 replaces ILS Y with ILS Z
&indep (ARR) EXPECT INDEPENDENT PARALLEL ILS [...]
&night (DEP) suppresses 18 not available message
&rnpx (ARR) EXPECT RNP X APCH RWY [...]
&southonly (DEP) ALL DEPARTING ACFT VIA MARUN, OBOKA AND TOBAK EXPECT SID WITH DESIGNATOR MIKE OR WHISKEY
&tailwind18 (DEP)
 TAILWIND COMPONENT RWY 18 MORE THAN 10 KT PILOTS UNABLE TO ACCEPT SHALL ADVISE ATC UPON START-UP REQUEST
&windshear07 WINDSHEAR RUNWAY 07L 07C AND 07R
&windshear18 WINDSHEAR RUNWAY 18
&windshear25 WINDSHEAR RUNWAY 25L 25C AND 25R
&windshearall WINDSHEAR ALL RUNWAYS
Automatic Setup
Remark
 Broadcast
standard expected approach message, when 2 runways are selected
 EXPECT DEPENDENT PARALLEL ILS Y APCH RWY [...] OR ILS APCH RWY [...]
active when RWY 18 selected as departure runway and 07R as arrival
 ACFT DEPARTING RWY 18 EXPECT POSSIBLE DEPARTURE FROM INTERSECTION MIKE, TORA 3454 METERS, IF UNABLE ADVISE TWR ON INITIAL CONTACT
active when RWY 25L selected as arrival runway and no LVP in progress
 DO NOT MISTAKE TWY MIKE FOR RWY 25C WHEN PERFORMING VISUAL APCH
active when RWY 18 is not selected as departure RWY
 RWY 18 NOT IN USE DUE TO TAILWIND
always shown, except when RNP X active
 EXPECT RADAR VECTORING, GLS APCH ON REQUEST

EDDL ATIS Codes

Manual Codes
CODE Broadcast
&acdm
 ALL IFR DEPS REPORT TOBT AT VACDM.VATGER.DE BEFORE REQ ENROUTE CLEARANCE
&windshearall
 CAUTION WINDSHEAR ALL RWYS
&const23l LANDING DISTANCE AVAILABLE RWY 23L 2400 METRES .. VACATE LATEST VIA TWY L8
&const23r LANDING DISTANCE AVAILABLE RWY 23R 2100 METRES .. IF ABLE VACATE VIA TWY K3 .. LATEST K4 .. RWY CLOSED WEST OF K4

EDDK ATIS Codes

Manual Codes
CODE Broadcast
&acdm
 ALL IFR DEPS REPORT TOBT AT VACDM.VATGER.DE BEFORE REQ ENROUTE CLEARANCE
&cdo
 EXPECT CDO FOR ILS APCH
&sra SRA APPROACH ON REQUEST
&windshearall
 CAUTION WINDSHEAR ALL RWYS

EDDS ATIS Codes

Manual Setup
CODE Broadcast
&acdm
 ALL IFR DEPS REPORT TOBT AT VACDM.VATGER.DE BEFORE REQ ENROUTE CLEARANCE
&sra
 SRA APPROACH AVAILABLE ON REQUEST

EDSB ATIS Codes

Automatic Setup
Remark
 Broadcast
standard message
 ADDITIONAL INFORMATION! CAUTION! CAT I HOLDING POINT ALPHA AND ECHO ARE LOCATED ON TAXIWAY GOLF SHORT BEHIND CAT II/III HOLDING POINT

EDFM ATIS Codes

Manual Setup
Remark
 Broadcast
&circling09 (select 09 as departure runway and 27 as arrival runway)
 adds CIRCLING 09 to expected approach message

EDFQ ATIS Setup

As EDFQ lacks its own certified METAR, automatic ATIS updates are currently not possible. However, an ATIS can still be generated manually using the following steps:

  • replace the $metar($atisairportA) parameter in the ATIS maker URL with the latest official EDFQ METAR
  • replace the EDFQ ICAO in the METAR with EDZZ
  • continue connecting the ATIS as usual

You will have to manually update the ATIS this way every time a new EDFQ METAR is published.

EDLA ATIS Setup

As EDLA lacks its own certified METAR, automatic ATIS updates are currently not possible. However, an ATIS can still be generated manually using the following steps:

  • replace the $metar($atisairportA) parameter in the ATIS maker URL with the latest EDLW METAR
  • replace the EDLW ICAO in the METAR with EDZZ
  • remove the &apptype and &depfreq parameters entirely
  • continue connecting the ATIS as usual

You will have to manually update the ATIS this way every time a new EDLW METAR is published.

Back to top